This document outlines all error codes reported by the CFLink protocol.

The below error codes are common across all devices, including error codes for Rule definitions.

• 001 = Does not comply with CFLink format
• 002 = Command not recognised
• 003 = Invalid Port Number
• 004 = Invalid Module Number
• 005 = Invalid Payload Field
• 006 = Invalid TGT CFLink ID
• 007 = Duplicate TGT CFLink ID Defined
• 008 = TGT CFLink ID is local Sub ID
• 009 = DID Invalid CFLink ID
• 010 = DID Invalid Serial Number

• 020 = RLW Invalid Payload
• 021 = RLW Invalid Address
• 022 = RLW Invalid Payload
• 021 = RLW Invalid Address
• 022 = RLW Invalid Rules Entry Start Address
• 023 = RLW Invalid Number of Macro
• 024 = RLW Invalid Macro Entry
• 025 = RLW Invalid Length of Macro Entry
• 026 = RLW Invalid Length of Macro Name
• 027 = RLW Invalid Macro Name
• 028 = RLW Macro Name is empty
• 029 = RLW Invalid Number of Actions
• 030 = RLW Invalid Action Entry
• 031 = RLW Invalid Length of Action Entry
• 032 = RLW Invalid Action Delay
• 033 = RLW Invalid Action Data
• 034 = RLW Action Data does not comply with CF Protocol
• 035 = RLW Action Data is Empty
• 036 = RLW Invalid Number of Rules
• 037 = RLW Invalid Rules Entry
• 038 = RLW Invalid Rules Name
• 039 = RLW Invalid Length of Search String
• 040 = RLW Invalid Search String
• 041 = RLW Search String is Empty
• 042 = RLW Invalid Length of mapped macro name
• 043 = RLW Invalid Macro Name in Rules Entry
• 044 = RLW Macro Name in Rules Entry is empty
• 045 = RLW Invalid ENDRLS Identifier
• 046 = RLW Unable to perform actions due to out of memory
• 047 = RLW Duplicate Macro Name
• 048 = RLW Macro Name in Rules Entry is not exist in Macro Entry
• 049 = RLW Duplicate Search String and Mapped Macro Name
• 050 = RLW Cumulative of Action Delay exceed the maximum value Invalid Rules Entry Start Address

The below error codes are common across all devices with an on-board RS232 port.

• 075 = Invalid COM Settings
• 076 = Invalid Mode
• 077 = Invalid Baudrate
• 078 = Invalid Data bit
• 079 = Invalid Parity bit
• 080 = Invalid Stop bit
• 081 = Invalid Flow Control
• 082 = SPW Invalid Data
• 083 = SPW Command, but not in 232 Mode

• 100 = Invalid IP Address
• 101 = Invalid Gateway
• 102 = Invalid Subnetmask
• 103 = Invalid DHCP Settings
• 104 = Invalid UDP Broadcast Settings
• 105 = Invalid TME Settings
• 106 = Invalid Year
• 107 = Invalid Month
• 108 = Invalid Date
• 109 = Invalid Day
• 110 = Invalid Hour
• 111 = Invalid Minute
• 112 = Invalid Seconds
• 113 = Invalid UTC Timezone
• 114 = Onboard Real Time Clock malfunction
• 115 = Invalid Slot Settings
• 116 = Invalid Slot Number
• 117 = Invalid Slot Mode
• 118 = Invalid Slot IP Address
• 119 = Invalid Slot Port Number
• 120 = Invalid Slot Timeout
• 121 = Invalid Slot Maximum Connections
• 122 = Invalid Slot TCP Echo Mode
• 123 = LANBridge number of TCP Connections exceed the maximum limit
• 124 = Invalid Subscription Settings
• 125 = Invalid Subscription Slot A
• 126 = Invalid Subscription Slot B
• 127 = Invalid Subscription CF ID
• 128 = Invalid Subscription Module
• 129 = Invalid Subscription TX Command
• 130 = Invalid Subscription RX Command
• 131 = Slot A and Slot B Identical
• 132 = Slot 2 is not subscribed to Slot 1
• 133 = SND Command Invalid Packet

• 249 = Invalid LED Mode
• 250 = Invalid Time Defined
• 251 = Invalid Count Defined
• 252 = Invalid LED Level Defined
• 253 = Max LED Level is less than Min LED Level
• 254 = Invalid LED Command

• 350 = Port P03/P04 cannot be 485H or 4XXF if P01/P02 is not also one of those 2.
• 351 = Pair modes (RS232H,485H and 4XXF)cannot be specified for ports P02 or P04.
• 352 = Flow control must be zero for any mode except 232.
• 353 = Buffer is full
• 354 = Invalid Port Write. Port is in OFF mode.

• 400 = Invalid Relay Pulse Time
• 401 = Invalid Relay Power On State
• 402 = Invalid Relay State

• 425 = PRT Invalid IO Port Mode
• 426 = PRT Invalid IO Port Minimum Change
• 427 = PRT Invalid IO Port Power On State
• 428 = SET Invalid IO State
• 429 = CFG Invalid IO Reporting Interval
• 430 = CFG Invalid IO Report On Change
• 431 = CFG Invalid IO Enabled

450 = SND Invalid IR Format Type 451 = SND Invalid IR Database Parameters 452 = SND Invalid IR Memory Parameters 453 = SND Invalid IR Raw Hex Code 454 = SND Invalid CF IR format 455 = SND <DEVICE> doesn't exist in MEM database 456 = SND <FUNCTION> doesn't exist in MEM database 457 = SND <DEVICE_CODE> doesn't exist in DBA database 458 = SND <DEVICE_TYPE> doesn't exist in DBA database 459 = SND <KEY_CODE> doesn't exist in DBA database 469 = DBA hardware error. UEI Gondar II (-3G) is out of synch. 470 = MEM database error. Invalid IRX format. 471 = Invalid IR Rules Format.